Peugeot 3008 Key Fob Problems
The mid-sized SUV from Peugeot, the 3008, has lots of positive attributes. It looks smart, drives well, and has a large boot. But can it fend against strong competition in the most crowded segment of the market?
If your Peugeot keyfob doesn't work it could have been exposed to clean or soapy tap water. You may need to remove the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by the coin-sized battery. This power is utilized to operate the remote locking mechanism and other features. This battery has a limited lifespan and can wear after years of use. A simple way to check whether the battery is defective is by performing an examination of voltage. A multimeter is used to determine the voltage between the battery's plus and the minus poles. The results of this test will show whether the battery is dead or not.
The receiver module could be the reason why the key fobs that you have not been able to use after using your Peugeot 3008 for a long period of time. The receiver module is responsible for capturing radio frequency signals from the key fobs, and then sending them to the car's system. If the receiver module is in issues, it will not be able to transmit commands to other modules within the car.
Another common cause for a non-working key fob is moisture or sweat on the circuit board. This can result in short circuits that drain the battery and can also cause the device to lose the remote locking feature of the key fob. If this is the case you must take your key fob in to a chip level service technician to repair it.
Water damage
Water damage could be a problem when you drop your keyfob in the pool pool, washed it or threw it out in the rain. Water is a good conductor and can cut off circuit boards. It can also cause corrosion to metal trace on the key fob and other components. A wet circuit board can also cause the battery to drain its charge.
If you have a spare key fob, try using it to unlock or lock your Peugeot 3008 to rule out the possibility that a dead battery is at the root of the problem. Interference signals can also cause your key fob to cease working properly. peugeot key replacement near me interfere with the signal transmitted by the receiver module. These interference signals can come from a wide range of things, including nearby radio transmitters.
If you hear sloshing sounds emanating from inside your Peugeot 3008 during your drive, it's probably because of a blocked condensate drain in the evaporator. You can identify this by taking a look at the drain holes that are underneath your door and blowing compressed air in the drain holes. You can also use flexible wire to move the drain holes around and dislodge any dirt that has accumulated there. Sloshing noises can be a sign that there are air pockets in the cooling system.
Faulty receiver module
The receiver module in a Peugeot 3008 is responsible for transmitting a remote keyless message from the keyfob into the receiver in the car. If the receiver module is damaged, it could stop the car from recognizing the key fob. This problem can also be caused by the battery being dead or water damage. Or, interference from electronic devices operating at the same frequency. In these situations an error message such as "card not detected" may appear on the display.
There are many ways to fix this problem. You can try replacing the battery or reprogramming your key fob. You can also use a spare key to start the car. However, if the key fob isn't working after these steps, it might be a chip defective.
The best way to tell if the key fob has an issue with its chip is to take it off and clean it with a paper towel and rubbing alcohol. If the chip is fried it is recommended to buy a new one. The FB Series enclosures come with the battery holder for coins that can be used with the most popular types of key fob batteries. They can also be personalized by using digital printing or CNC cutouts that are machined. If your key fob was exposed to salty or dirty tap water, the chip might be contaminated and require to be cleaned.
Keyless entry system malfunctions
If you are seeing "card not detected", this means that your car cannot receive a signal sent by your key fob. This could be due to many reasons, including an insufficient or dead battery. The issue is usually resolved by pressing the start button on the key fob. In certain cases, you might be required to take the keyfob to a Peugeot dealer for repairs.
The first step to fix the issue with a Peugeot 3008 key fob that isn't able to unlock or lock the doors is to check its battery. Batteries are typically the cause of malfunctioning key fobs. However there are other factors that could be at play. They include worn buttons, damage to the receiver module, water problems and signal interference.
If your Peugeot key fob has been exposed to pure tap water, it's an ideal idea to remove the battery. Then, dry the electronic components using paper towels. You can also use a cleaner or isopropyl ethanol to do this. If the fob has been exposed to salt or soapy water, it's best to replace it.
If your key fob is still not working, try to reset it by disconnecting the battery with 12 volts for approximately 15 minutes. Connect the negative cable, then the positive cable.